Navcom SF-3050 Logging Data to USB Using SurvCE Bedienungsanleitung PDF herunterladen

Applications Note – Logging Data to USB Using SurvCE - SF-3050

Rev. A i Release - Dec 09

This guide will step you through logging GNSS receiver data to the SF-3050 USB Host port via Carlson

Software’s SurvCE data collector program. The receiver data may be used for post-processing or troubleshooting.

 The following additional hardware is required for this interface:

o Positronic 9-Pin Male to USB 2.0 Host Receptacle Data Cable,

P/N 94-310271-3006LF

o An un-partitioned USB Flash Drive

 SurvCE software version 2.30.47 (Beta release) or later is required for

this interface

 The procedure which follows applies to all released versions of SF-3050

firmware

Procedure

 Create a data logging command file. A sample file is provided below:

Data Logging Setup.txt:

[USBMODE]HOST

[OUTPUT]PANICA,ONCHANGE,,FH1

[OUTPUT]??,ONCHANGE,,FH1

[OUTPUT]OK,ONCHANGE,,FH1

[LOGFILE]start

[OUTPUT]MSGVERSION,ONTIME,600,FH1

[OUTPUT]MSGPRODUCTINFO,ONCE,,FH1

[OUTPUT]MSGPRODUCTINFO,ONTIME,600,FH1

[PROFILE]OUTPUT

[OUTPUT]EPHEM1B,ONCE,,FH1

[OUTPUT]ALM1B,ONCE,,FH1

[OUTPUT]ECHODGPSB,ONCHANGE,,FH1

[OUTPUT]CHNLSTATUS1B,ONTIME,1,FH1

[OUTPUT]PVT1B,ONTIME,1,FH1

[OUTPUT]MEAS1B,ONTIME,1,FH1

[OUTPUT]EPHEM1B,ONCHANGE,,FH1

[OUTPUT]ALM1B,ONCHANGE,,FH1

 Copy this file to the data collector

 Connect the data collector to the SF-3050 via either the receiver Bluetooth port or Com1 – RS-232

 Connect the USB 2.0 Host Data Cable to SF-3050 Com2

 Connect the USB Flash Drive to the USB 2.0 Host Data Cable

 Turn the receiver and data collector on and start the SurvCE program

 Establish a connection between the data collector and the SF-3050 (either Rover or Base, as appropriate)

 Select the Equip tab

 Click on GPS Utilities

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Procedure

Applications Note – Logging Data to USB Using SurvCE - SF-3050Rev. A i Release - Dec 09This guide will step you through logging GNSS receiver data to

Seite 2

Applications Note – Logging Data to USB Using SurvCE - SF-3050Rev. A ii Release - Dec 09 Click on Send Command Click on Send File Locate the Dat

Seite 3

Applications Note – Logging Data to USB Using SurvCE - SF-3050Rev. A iii Release - Dec 09 At the completion of the file transer, a confirmationwindo

Seite 4 - Rev. A iv Release - Dec 09

Applications Note – Logging Data to USB Using SurvCE - SF-3050Rev. A iv Release - Dec 09

Kommentare zu diesen Handbüchern

Keine Kommentare

Navcom SF-3050 Logging Data to USB Using SurvCE Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Navcom SF-3050 Logging Data to USB Using SurvCE herunter. NavCom SF-3050 Logging Data to USB Using SurvCE User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Navcom SF-3050 Logging Data to USB Using SurvCE